Garment Cover RFQs: Match the Hanger Hook Opening
How can a buyer confirm the hook fits the cover opening?
To confirm that a hanger hook fits through the top of an open-bottom garment cover, send the supplier the exact hanger used by your team. Ask for a marked drawing of the top opening and a sample demonstration showing how the hook passes through and how the cover sits on the hanger. Link the evidence to the quoted cover and hanger references.

Identify the hanger that will be used in the shop
The Wuse PEVA Open-Bottom Garment Cover listing shows garments suspended on different hanger shapes, with the hook visible above the cover. These views identify the product and the part of the cover to review. Ask the supplier for a close view of the offered top opening. The catalogue pictures do not give its dimensions or show how a buyer’s specific hook passes through it.
Provide the supplier with a hanger sample, supplier item code or marked drawing. Include a side view of the hook so the supplier can see its profile, and point out the widest part that would have to pass through the cover. If the hook has a wider section near its base, include that area in the drawing. Give each hanger a separate reference when the buyer uses more than one style.
Ask for the opening shape and position on the quoted cover
Request a close photo or drawing of the top area laid flat. Ask the supplier to outline the opening and state how it measures each span. For a narrow or irregular shape, ask it to mark the portion that controls passage of the hanger hook. Also have it show where the opening sits relative to an identifiable point on the cover, such as the centre of the top edge or a seam visible on the sample.
Include the exact cover reference in that request. The supplier may offer several catalogue sizes, so ask whether the drawing applies to every size being quoted or only the sample shown. If it uses a different opening shape or position for another version, record that version separately. Have the supplier put the measurement unit and revision on the drawing so the buyer can compare it with the hanger reference.

Ask the supplier to show how the hook passes through
Request two views of the same sample. The first should show the hook partway through the top opening, with the hanger orientation visible. The second should show the cover after it is in position on the hanger. Ask the supplier to use the procedure it intends the buyer to follow and to point out any turning or repositioning it needed for this particular combination.
A hook can look narrow from the front while its bend extends farther in a side view. Ask for the view that shows the widest portion relative to the opening. If the supplier changes to a narrower hanger to make the demonstration, ask for a second check using the intended hanger. Keep the supplier’s explanation with the photos so the buyer can tell which parts and orientation were actually assessed.
Review where the cover sits after fitting
Ask for a front photo of the upper cover and hanger in their final positions. Show the hanger’s centre and ask the supplier to mark the opening beside it. If the cover sits to one side or the top edge looks gathered, ask for a closer view and an explanation of which feature is affecting the position. The buyer can then decide whether the demonstrated fit is acceptable for the way the garments will be presented.
Make the acceptance condition explicit in the enquiry. For example, a shop that changes covers at a preparation station may ask the supplier to show that staff can fit the cover using its standard hanger and the approved orientation. A buyer using two hanger profiles can ask for both combinations to be demonstrated, with a separate reference on each set of photos.

Keep the opening evidence with the quote
| Buyer question | Supplier evidence to request | What to retain |
|---|---|---|
| Which cover? | Offered product, size and sample reference | Exact quote line |
| Which hanger? | Item reference and view of the full hook profile | Buyer hanger sample or drawing revision |
| What opening? | Marked shape, measured spans and location on the top area | Opening drawing or photo reference |
| How does the hook pass through? | Close view with the demonstrated orientation visible | Fitting view for the exact combination |
| Where does the cover sit? | Final front view showing the top area on the hanger | Accepted position and sample identifier |
Ask the supplier to attach the marked record to the offer. If it revises the opening or proposes another hanger, ask for an updated demonstration before approving that combination. Send the hanger and cover references through the Wuse contact page so the supplier can identify the product and the sample task in one enquiry.
- Show the supplier the intended hanger and its hook profile.
- Request a marked view of the top opening and photos during and after fitting.
- Keep the accepted opening and hanger references on the quote.
Frequently asked questions
Does a catalogue photo show which hook profiles fit?
It shows the hanger pictured with the product. Request a fitting demonstration using your specified hanger and the quoted cover.
What if the supplier uses one opening across several cover sizes?
Ask it to identify the applicable sizes on the drawing and confirm which size and hanger were used for the demonstration.
How do I review two hanger styles?
Give each hanger a reference and ask for a separate fitting and final position view for each combination you plan to buy.